CALI Grown E85 Street Car: Project BLACKADDE

MotoTek · 07-22-2009, 10:48 PM

So, I started this project last August thinking that I was going to leave the car at the body shop to install the RE-Amemiya ADGT widebody, and then I decided I wanted to do just a few small upgrades.

It began with wanting to port the motor to go single, run E85, completely redoing the suspension, new interior, really putting a brand new car together. I even got some nice valve stem caps.

I'm hoping by posting this thread I'll get some more motivation to finish the project. I'm trying to take her to Seven Stock XII this year, but unfortunately with a full time college students budget it doesn't look like it's going to happen. So, I'm currently in the process of looking for sponsors to bring my baby to life.

Ben "Karack" @ Rotary Evolution in Northern California will be the engine builder/tuner, and will be updating me/us with pictures of the engine build.

Anyway, hope everyone enjoys the build thread.

MOD LIST
Some of these parts will change as we get down to the finish.

ENGINE:
Large Street Port
RA 2mm Super Seals
Atkins Gasket Kit
Atkins Thermal Pellet
Atkins Solid Corner Seals
OEM 2mm Apex Seal Springs
OEM Corner Seal Springs
OEM Side Seals
OEM Side Seal Springs
OEM O Rings
OEM Oil Control Rings
OEM Oil Ring Springs
OEM Front & Rear Main Seal
OEM Pilot Bearing & Seal
OEM Rotor Bearings
OEM Stationary Gear Bearings

FUEL: (E85)
CJ-Motorsports Fuel Rails
Injector Dynamics 6 x 1000cc
Kevlar Enforced Aeroquip Startlite Hose
Aeromotive 13109 Fuel Pressure Regulator
Aeromotive Eliminator Fuel Pump
Aeromotive P/N 12304 & P/N 12335 Fuel Filters
ATL Fuel Cell

SUSPENSION/DRIVETRAIN:
Exedy Twin Plate Cerametallic Clutch ZM022SD
AtomicRex Aluminum Manual Steering Rack
WideFoot SwayBar (Mounts, Bearings, & Spacers)
Tri-Point Engineering Front & Rear Sway Bars
Super Now Toe Links
Super Now Trailing Arms
Super Now Tie Rod Ends
Delrin Bushing Set
OEM Pillowball Bushings/Dust Seals
FEED Tower Bar

COOLING::
Koyo N-Flow
GReedy 3 Row FMIC
FEED Throttle Body Elbow
FEED Ported Throttle Body
RE-Speed Oil Filler Neck
RE-Speed Oil Filler Pedestal -10
Super Now Main Pulley
Super Now Water Pump Pulley
Super Now Alternator Pulley
Xcessive Lower Intake Manifold

EXTERIOR:
RE-Amemiya ADGT WideBody
RE-Amemiya AD9 CF Bonnet
RE-Amemiya FRP Fender Mirrors
Carbon Fiber Hatch
Flying 'M' Badges
Feed Halogen Turn Lamps
OEM 99 Spec Rear Turn Lamps
WHEELS TBA!!!!!! Looking for sponsors!!!

INTERIOR:
RaceShop 4pt Roll Bar
Brand New OEM (Gauge surround, hood, chrome bezel, a/c panel, shifter panel, shifter surround)
FlyRX7 60mm Tripod
OMP WRC Steering Wheel
NRG (Quick Release v2.0, Lock, & Adapter)
RE-Amemiya Scuff Plates
RedLine Italian Leather Shift Boots
JDM Arm Rest Pad
Sparco Evo CF Racing Seats

ELECTRONICS:
Microtech LT-10
HKS EVC Boost Controller
DEFI BF Boost
DEFI BF Fuel Pressure
DEFI BF Oil Pressure
DEFI BF EGT
Innovative LC1 Wideband

EXHAUST:
Apexi GT Spec
Custom 4" turbo Back V-Band

TURBO:
TBA!!! Not sure what I'm doing yet.

MISC:
Rotary13B1 Rotor Dipstick
Rotary13B1 Rotary Engine Keychain
Rotary13B1 Valve Stem Caps
FEED Oil Filler Cap
FEED PS Reservoir Cap
Xcessive Oil Pan

Boxes of goodies.

M2 4 point roll bar.

RE-Amemiya ADGT Widebody.

Some random stuff.

FEED Throttle Body Elbow.

FEED Strut Bar.

MotoTek · 07-22-2009, 10:49 PM

Fuel Rails custom anodized purple.

Some brand new interior stuff... there's actually a lot more than this. Going for the brand new car smell.

Manual Steering rack.

Some suspension stuff.

Rotary#10 · 07-27-2009, 01:02 AM

Where did you pick up that steering manual rack?

Phoenix7 · 07-27-2009, 01:17 AM

damn, you gotta finish it man! Can't wait to see it.

prrex4ever · 07-27-2009, 05:06 PM

Quote:

Originally Posted by Rotary#10

Where did you pick up that steering manual rack?

Saw it on the "other" site, but it's also being discussed here in the 3rd gen. section.

MotoTek · 07-27-2009, 06:04 PM

Manual rack is from Atomic Rex. Email Jon: Racing@atomicrex.co.uk

Phoenix...I'm trying man. I'd love to drive down with everyone from the norcal to 7stock.

MaczPayne · 07-28-2009, 04:36 PM

What kind of numbers are you shooting for?

MotoTek · 07-29-2009, 07:44 PM

600+ on high boost....500+ on low

I've been having a lot of problems with the body shop I went to, so I'm looking for someone else to take it too. The 1st place was a family friend, and he really doesn't care about my project, and hasn't put forward the quality work I am looking for.

Good news is that I already know who to take it to, just got to see if he has time for it. He always has 5-10 cars he's working on.

***Herblenny*** · 07-29-2009, 09:37 PM

Can't wait to see the car!

MotoTek · 07-30-2009, 01:18 PM

Thanks Phil. Hopefully it looks half as good as your FD's.

pics of the authentic 99 spec tails

***Herblenny*** · 07-30-2009, 02:01 PM

I'm sure it will look better than mine... Can't wait to see it!

classicauto · 07-30-2009, 03:56 PM

Quote:

Originally Posted by MotoTek

I've been having a lot of problems with the body shop I went to, so I'm looking for someone else to take it too. The 1st place was a family friend, and he really doesn't care about my project, and hasn't put forward the quality work I am looking for.

If only you lived in Ontario, I'd gladly make you need jaw surgery from the drop that would occur when you saw it finished

Best of luck with the car, looks like one HELL of a project with no corners cut - me rikey very much!

MotoTek · 08-08-2009, 07:59 PM

since your here classic, do you know of any really nice factory pearl paints?

I was thinking of doing a:
1)diamond black like the Volk TE37's
2) Opal Black form a GTR.
3) Jet Black with Purple Pearl

Thinking about going to the Lexus dealership and checking out some colors too.

BigIslandSevens · 08-26-2009, 07:32 PM

Mazda makes a Sparkling black Mica( pearl) I sprayed a buddies FC in this and it is crazy in the sunlight. Pops like 4 different pearls in it. PPG code # 914021 I believe. This is from the 2008 color book under the Mazda section. Kinda $$ though. I think it was 150 a quart.

Nice project you have going. Should be sick at the end.

classicauto · 08-27-2009, 09:24 AM

Quote:

Originally Posted by MotoTek

since your here classic, do you know of any really nice factory pearl paints?

I was thinking of doing a:
1)diamond black like the Volk TE37's
2) Opal Black form a GTR.
3) Jet Black with Purple Pearl

Thinking about going to the Lexus dealership and checking out some colors too.

Yeah i can think of a few.....the Opal GTR colour is nice...I'll dig up some codes for ya

07-22-2009, 10:49 PM	#2
MotoTek Always Under Construction Join Date: Mar 2008 Location: La Playa, CA Posts: 302 Rep Power: 18	Fuel Rails custom anodized purple. Some brand new interior stuff... there's actually a lot more than this. Going for the brand new car smell. Manual Steering rack. Some suspension stuff. __________________ BLACKADDE™ \| ADGT RX7 \|

07-27-2009, 01:02 AM	#3
Rotary#10 Rotorhead Join Date: Sep 2008 Location: "the town " Oakland Posts: 219 Rep Power: 17	Where did you pick up that steering manual rack? __________________ Currently running: 90 GTUs converted to S5 TurboII. Track car. 90 N/A GTUs.. Running project car 89 N/A GTUs in Black #2 10/6/18 Blown coolant seal undergoing rebuild and restomod.

07-27-2009, 06:04 PM	#6
MotoTek Always Under Construction Join Date: Mar 2008 Location: La Playa, CA Posts: 302 Rep Power: 18	Manual rack is from Atomic Rex. Email Jon: Racing@atomicrex.co.uk Phoenix...I'm trying man. I'd love to drive down with everyone from the norcal to 7stock. __________________ BLACKADDE™ \| ADGT RX7 \|

07-28-2009, 04:36 PM	#7
MaczPayne Bah! Join Date: Mar 2008 Location: Riverside, SoCal Posts: 442 Rep Power: 18	What kind of numbers are you shooting for? __________________ Johnson TA FC in the works!

07-29-2009, 07:44 PM	#8
MotoTek Always Under Construction Join Date: Mar 2008 Location: La Playa, CA Posts: 302 Rep Power: 18	600+ on high boost....500+ on low I've been having a lot of problems with the body shop I went to, so I'm looking for someone else to take it too. The 1st place was a family friend, and he really doesn't care about my project, and hasn't put forward the quality work I am looking for. Good news is that I already know who to take it to, just got to see if he has time for it. He always has 5-10 cars he's working on. __________________ BLACKADDE™ \| ADGT RX7 \|

07-22-2009, 10:48 PM	#1
MotoTek Always Under Construction Join Date: Mar 2008 Location: La Playa, CA Posts: 302 Rep Power: 18	CALI Grown E85 Street Car: Project BLACKADDE So, I started this project last August thinking that I was going to leave the car at the body shop to install the RE-Amemiya ADGT widebody, and then I decided I wanted to do just a few small upgrades. It began with wanting to port the motor to go single, run E85, completely redoing the suspension, new interior, really putting a brand new car together. I even got some nice valve stem caps. I'm hoping by posting this thread I'll get some more motivation to finish the project. I'm trying to take her to Seven Stock XII this year, but unfortunately with a full time college students budget it doesn't look like it's going to happen. So, I'm currently in the process of looking for sponsors to bring my baby to life. Ben "Karack" @ Rotary Evolution in Northern California will be the engine builder/tuner, and will be updating me/us with pictures of the engine build. Anyway, hope everyone enjoys the build thread. MOD LIST Some of these parts will change as we get down to the finish. ENGINE: Large Street Port RA 2mm Super Seals Atkins Gasket Kit Atkins Thermal Pellet Atkins Solid Corner Seals OEM 2mm Apex Seal Springs OEM Corner Seal Springs OEM Side Seals OEM Side Seal Springs OEM O Rings OEM Oil Control Rings OEM Oil Ring Springs OEM Front & Rear Main Seal OEM Pilot Bearing & Seal OEM Rotor Bearings OEM Stationary Gear Bearings FUEL: (E85) CJ-Motorsports Fuel Rails Injector Dynamics 6 x 1000cc Kevlar Enforced Aeroquip Startlite Hose Aeromotive 13109 Fuel Pressure Regulator Aeromotive Eliminator Fuel Pump Aeromotive P/N 12304 & P/N 12335 Fuel Filters ATL Fuel Cell SUSPENSION/DRIVETRAIN: Exedy Twin Plate Cerametallic Clutch ZM022SD AtomicRex Aluminum Manual Steering Rack WideFoot SwayBar (Mounts, Bearings, & Spacers) Tri-Point Engineering Front & Rear Sway Bars Super Now Toe Links Super Now Trailing Arms Super Now Tie Rod Ends Delrin Bushing Set OEM Pillowball Bushings/Dust Seals FEED Tower Bar COOLING:: Koyo N-Flow GReedy 3 Row FMIC FEED Throttle Body Elbow FEED Ported Throttle Body RE-Speed Oil Filler Neck RE-Speed Oil Filler Pedestal -10 Super Now Main Pulley Super Now Water Pump Pulley Super Now Alternator Pulley Xcessive Lower Intake Manifold EXTERIOR: RE-Amemiya ADGT WideBody RE-Amemiya AD9 CF Bonnet RE-Amemiya FRP Fender Mirrors Carbon Fiber Hatch Flying 'M' Badges Feed Halogen Turn Lamps OEM 99 Spec Rear Turn Lamps WHEELS TBA!!!!!! Looking for sponsors!!! INTERIOR: RaceShop 4pt Roll Bar Brand New OEM (Gauge surround, hood, chrome bezel, a/c panel, shifter panel, shifter surround) FlyRX7 60mm Tripod OMP WRC Steering Wheel NRG (Quick Release v2.0, Lock, & Adapter) RE-Amemiya Scuff Plates RedLine Italian Leather Shift Boots JDM Arm Rest Pad Sparco Evo CF Racing Seats ELECTRONICS: Microtech LT-10 HKS EVC Boost Controller DEFI BF Boost DEFI BF Fuel Pressure DEFI BF Oil Pressure DEFI BF EGT Innovative LC1 Wideband EXHAUST: Apexi GT Spec Custom 4" turbo Back V-Band TURBO: TBA!!! Not sure what I'm doing yet. MISC: Rotary13B1 Rotor Dipstick Rotary13B1 Rotary Engine Keychain Rotary13B1 Valve Stem Caps FEED Oil Filler Cap FEED PS Reservoir Cap Xcessive Oil Pan Boxes of goodies. M2 4 point roll bar. RE-Amemiya ADGT Widebody. Some random stuff. FEED Throttle Body Elbow. FEED Strut Bar. __________________ BLACKADDE™ \| ADGT RX7 \| Last edited by MotoTek; 07-22-2009 at 10:59 PM.

07-29-2009, 09:37 PM	#9
*Herblenny* Founder/Administrator/Internet Pitbull :) Join Date: Jan 2008 Posts: 644 Rep Power: 10	Can't wait to see the car! __________________ DGRR 2013 - Year of 13B www.DealsGapRotaryRally.com http://www.facebook.com/Herblenny

07-30-2009, 01:18 PM	#10
MotoTek Always Under Construction Join Date: Mar 2008 Location: La Playa, CA Posts: 302 Rep Power: 18	Thanks Phil. Hopefully it looks half as good as your FD's. pics of the authentic 99 spec tails __________________ BLACKADDE™ \| ADGT RX7 \|

07-30-2009, 02:01 PM	#11
*Herblenny* Founder/Administrator/Internet Pitbull :) Join Date: Jan 2008 Posts: 644 Rep Power: 10	I'm sure it will look better than mine... Can't wait to see it! __________________ DGRR 2013 - Year of 13B www.DealsGapRotaryRally.com http://www.facebook.com/Herblenny

08-08-2009, 07:59 PM	#13
MotoTek Always Under Construction Join Date: Mar 2008 Location: La Playa, CA Posts: 302 Rep Power: 18	since your here classic, do you know of any really nice factory pearl paints? I was thinking of doing a: 1)diamond black like the Volk TE37's 2) Opal Black form a GTR. 3) Jet Black with Purple Pearl Thinking about going to the Lexus dealership and checking out some colors too. __________________ BLACKADDE™ \| ADGT RX7 \|

08-26-2009, 07:32 PM	#14
BigIslandSevens Rotary Fanatic Join Date: Feb 2008 Location: Denver, NC Posts: 201 Rep Power: 18	Mazda makes a Sparkling black Mica( pearl) I sprayed a buddies FC in this and it is crazy in the sunlight. Pops like 4 different pearls in it. PPG code # 914021 I believe. This is from the 2008 color book under the Mazda section. Kinda $$ though. I think it was 150 a quart. Nice project you have going. Should be sick at the end.