my nephews Turbo II. 8lbs of boost.

Judge Ito · 10-22-2010, 07:23 PM

my nephew Raz and I just spent the last 3 weeks working on his turbo II. here we just finish street tuning his haltech @ 8psi of boost. car pulls strong all through the rpms. we are getting this car ready for Maryland and the import vs domestic event. car will be raced @ 22psi of boost at the event. enjoy the video..

mods are:
series 4 engine
streetport with all new seals clearanced to tight specs.
haltech F10
2 1000cc primaries and 1600cc secondarys
2 msd6al with 2 steps
act clutch kit
bosch in-tank fuel pump
aeromotive fpr
front mount intercooler.

http://www.youtube.com/watch?v=Ez3HvxXyKGM

Judge Ito · 10-24-2010, 07:15 PM

2 step installed.. enjoy the video..

http://www.youtube.com/watch?v=KKPpIpPu5X4

89fc3s · 10-24-2010, 09:47 PM

that fireball in the second video was so loud that camera couldnt even pick it up lol

Judge Ito · 03-26-2011, 06:57 AM

update on my nephews turbo II. yesterday we dynoed the car. made 400rwhp @ 15lbs of boost. tried to dyno at 22psi but the car would not hold more then 15lbs. we will be looking into the boost leak, fix it and go back to the dyno. turbo is an innovative..

diabolical1 · 03-26-2011, 08:34 AM

sounds like a good result. i shudder to think of what another 7 pounds will yield.

Judge Ito · 03-26-2011, 04:51 PM

Quote:

Originally Posted by diabolical1

sounds like a good result. i shudder to think of what another 7 pounds will yield.

im looking forward to seeing more results here. so far everything looks promising. we had the intention to video the dyno runs, but all that carbon monoxide had me ready to run out of there. pig rich on the air fuel mixtures..

RotaryXperiment · 03-26-2011, 05:08 PM

nice,good job ito!

Judge Ito · 03-26-2011, 05:26 PM

Quote:

Originally Posted by RotaryXperiment

nice,good job ito!

thanks alex. this engine also uses the goopy refinish

rx71king · 03-26-2011, 11:35 PM

what's the timing on that bad boy....are you running the leading through the cap and rotor.?...sounds on point.........good luck at the event

Judge Ito · 03-27-2011, 05:49 AM

Quote:

Originally Posted by rx71king

what's the timing on that bad boy....are you running the leading through the cap and rotor.?...sounds on point.........good luck at the event

running leading off the distributor cap. mite not go to the event. it's freezing outside..

10-22-2010, 07:23 PM	#1
Judge Ito Porting Master Join Date: Mar 2009 Location: North Jersey, USA Posts: 154 Rep Power: 17	my nephews Turbo II. 8lbs of boost. my nephew Raz and I just spent the last 3 weeks working on his turbo II. here we just finish street tuning his haltech @ 8psi of boost. car pulls strong all through the rpms. we are getting this car ready for Maryland and the import vs domestic event. car will be raced @ 22psi of boost at the event. enjoy the video.. mods are: series 4 engine streetport with all new seals clearanced to tight specs. haltech F10 2 1000cc primaries and 1600cc secondarys 2 msd6al with 2 steps act clutch kit bosch in-tank fuel pump aeromotive fpr front mount intercooler. http://www.youtube.com/watch?v=Ez3HvxXyKGM

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

10-24-2010, 07:15 PM	#2
Judge Ito Porting Master Join Date: Mar 2009 Location: North Jersey, USA Posts: 154 Rep Power: 17	2 step installed.. enjoy the video.. http://www.youtube.com/watch?v=KKPpIpPu5X4

10-24-2010, 09:47 PM	#3
89fc3s rotary powaaa Join Date: Jun 2008 Location: Charlotte NC Posts: 47 Rep Power: 0	that fireball in the second video was so loud that camera couldnt even pick it up lol

03-26-2011, 06:57 AM	#4
Judge Ito Porting Master Join Date: Mar 2009 Location: North Jersey, USA Posts: 154 Rep Power: 17	update on my nephews turbo II. yesterday we dynoed the car. made 400rwhp @ 15lbs of boost. tried to dyno at 22psi but the car would not hold more then 15lbs. we will be looking into the boost leak, fix it and go back to the dyno. turbo is an innovative..

03-26-2011, 05:08 PM	#7
RotaryXperiment Rotary Fanatic Join Date: Mar 2008 Location: Bradenton, Fl Posts: 136 Rep Power: 18	nice,good job ito!

03-26-2011, 11:35 PM	#9
rx71king Rotary Fanatic Join Date: Jul 2009 Location: queens ny Posts: 117 Rep Power: 16	what's the timing on that bad boy....are you running the leading through the cap and rotor.?...sounds on point.........good luck at the event