|
|||||||
| RX-7 2nd Gen Specific (1986-92) RX-7 1986-92 Discussion including performance modifications and technical support sections. |
 |
|
|
Thread Tools | Display Modes |
|
|||||||
| RX-7 2nd Gen Specific (1986-92) RX-7 1986-92 Discussion including performance modifications and technical support sections. |
|
|
|
Thread Tools | Display Modes |
12-11-2011, 01:44 PM
|
#1 |
|
I have Ultra power in me.
Join Date: Sep 2011
Posts: 457
Rep Power: 15  |
Replacing bearing in S4 TII rear end.
I was told the noise that my diff is making is due to the bearing going bad. I was wondering if any one has a write up or know how to replace them, and exactly what parts I should order before I start taking it apart.
|
|
|
|
12-13-2011, 12:33 AM
|
#2 |
|
Rotary Fanatic
Join Date: Jan 2010
Posts: 253
Rep Power: 16 |
http://www.rx7club.com/showthread.php?t=326078
this is what i have looked up because im gonna do the same thing to my car soon sorry its from the the evil forum |
|
|
|
|
12-13-2011, 04:26 PM
|
#3 |
|
I have Ultra power in me.
Join Date: Sep 2011
Posts: 457
Rep Power: 15 |
No, this is inside the diff.
|
|
|
|
|
12-13-2011, 09:33 PM
|
#4 | |
|
RCC Addict
Join Date: Mar 2008
Location: Honolulu, Hawaii USA
Posts: 1,813
Rep Power: 19 |
The Mazda FSM has all the details to take care of this job.
Only warning about the replacement is the preloaded crush washer in the pinion gear. Also be prepared to redo the pinion gear to ring gear clearancing procedure which can be a PITA... -Ted
__________________
reted_2000@yahoo.com Technical Advisor FC3S Pro http://fc3spro.com/ Quote:
|
|
|
|
|
|
12-14-2011, 12:32 AM
|
#5 |
|
I have Ultra power in me.
Join Date: Sep 2011
Posts: 457
Rep Power: 15 |
Is it better to drop the subframe and remove the diff or leave it on the car??
|
|
|
|
|
12-14-2011, 01:51 AM
|
#6 | |
|
RCC Addict
Join Date: Mar 2008
Location: Honolulu, Hawaii USA
Posts: 1,813
Rep Power: 19 |
The instructions are for the rear diff to be removed.
I would think it would be too much trouble to leave it mounted. I'd think the subframe would get in the way? Remember, the rear portion of the rear diff has the upper, rear mounts on it. To remove the internals, you need to separate the case. -Ted
__________________
reted_2000@yahoo.com Technical Advisor FC3S Pro http://fc3spro.com/ Quote:
|
|
|
|
|
|
12-14-2011, 11:23 AM
|
#7 | |
|
Test Whore - Admin
Join Date: Mar 2008
Location: Right Behind you son
Posts: 4,581
Rep Power: 10 |
Quote:
__________________
-The Angry Stig- DGRR 2009, 2011, 2012 & 2013 - Best FC DEALS GAP!! WOOHOOOO!!!!! 2015 Audi S4 - Samantha - Zero Brap S4 2004 RX8 - Jocelyn - 196rwhp, 19mpg fuel to noise converter 2000 Jeep Cherokee Sport - Wifey mobile - Now with 2.5" OME lift and 30" BFG AT KO's! So it begins 1998 Jeep Cherokee - 5 spd, 4" lift, 33" BFG's - Rotary Tow Vehicle 1988 'Vert - In progress 1988 FC Coupe - Gretchen -The attention whore BEAST! I'm a sick individual, what's wrong with you? I'm pure Evil I'm still insane, in the best possible way. I think Brian's idea of romance is using lube. Your rage caused the meteor strike in Russia. The Antichrist would be proud of his minion. You win with your thread. Most everything It's a truck with a steel gate on the back. Just a statement of fact Motec M820, AIM dash, ported 13B-RE Cosmo, 6-spd trans, 4.3 Torsen, custom twin wg fully divided mani, Custom 4" split into 2x 3" exhaust, Custom HMIC, Custom custom custom custom I like to welder stuff.... No Bolt-ons allowed. Dyno'ed @ Speed1 Tuned by me - 405rwhp on WG.... WM50 cuming soon. -Angry Motherf*cker Mode ENGAGED- |
|
|
|
|
|
03-12-2016, 01:12 PM
|
#8 | |
|
I have Ultra power in me.
Join Date: Sep 2011
Posts: 457
Rep Power: 15 |
Quote:
That was a dumb question I amit now. After I did a little research I found out a bad bearing my cause damage to the ring gear and pinion. Does any body other the mazda make a replace Ring and gear set for the S4 TII rearend? $750 seems like a rebuild is not cost effective. |
|
|
|
|
|
| Bookmarks |
|
|
Linear Mode
