Quote:
Originally Posted by Johnny_K
Hope it gets done but body shops seem to always over deliver.
|
Quote:
Originally Posted by Johnny_K
You have the car with you and you are building the harness and it's still taking you X amount of weeks?
|
Yeah, historically I only get a chance to work on the cars on the weekend. Tonight though, Maggie has her art thing so home is mine until about 22:00. So I'll have the harness laid out on the dining room table striping, crimping, and terminating the harness from the Firewall forward. Saturday after the snow I'll head to the shop and build the back half
Quote:
Originally Posted by Johnny_K
You will then install the harness and set the base map.
|
Few minutes to get the basemap loaded and the thing running. I'm driving and tuning an FD now that is incredibly similar to Pete's engine. Should need very minor adjustments before he can make the 200is mile run back to MD next weekend
Quote:
Originally Posted by Johnny_K
Peter breaks the engine in and then drive or trailer the car to you and have it tuned.
|
Two weeks and then we'll be good to tune. He'll just drive it up
Quote:
Originally Posted by Johnny_K
Kyle has to buy an haltech and all the sensors.
|
I have a PS2k harness that I could finish up in a day and sell to him with all the sensors needed. Integrating it to his S5 would be slightly time consuming though, like maybe a day to feed it the power, ground and turn on's that it needs.
Quote:
Originally Posted by Johnny_K
I would think you would charge him some money to build the harness
|
They start @ $2k installed
Quote:
Originally Posted by Johnny_K
He then has to install a harness that was built remotely and hope that the length and sensor are in the right place. I know you can get it close. Not sure if the harness will just be plug and play either. Got to wire in power, ground, prob fuel pump power,speedo and rpm.
|
The ideal way to do it would be to send me some measurements for the harness from the firewall forward. Build that completely and then head down to get it all installed.
Quote:
Originally Posted by Johnny_K
Once everything is connected and it doesn't start, he has to rely on a few local friend to come over and help or call you.
|
And I would be very little help because without seeing it, I've already given him all the advice I've got. Now it's really oddball shit that needs to be looked at
Quote:
Originally Posted by Johnny_K
I sound like a big pessimistic and hope it all works out if Kyle goes Haltech but i don't think that's his answer to his problem.
|
I told him that too.... at this point the helltech is nothing more than a really expensive piece of diagnostic equipment. Of course I could be wrong and the helltech will fix everything, but I suspect that there's a mechanical problem, or electrical, that hasn't been found yet.
__________________
-The Angry Stig-
DGRR 2009, 2011, 2012 & 2013 - Best FC
DEALS GAP!! WOOHOOOO!!!!!
2015 Audi S4 - Samantha - Zero Brap S4
2004 RX8 - Jocelyn - 196rwhp, 19mpg fuel to noise converter
2000 Jeep Cherokee Sport - Wifey mobile - Now with 2.5" OME lift and 30" BFG AT KO's! So it begins
1998 Jeep Cherokee - 5 spd, 4" lift, 33" BFG's - Rotary Tow Vehicle
1988 'Vert - In progress
1988 FC Coupe - Gretchen -The attention whore BEAST!
I'm a sick individual, what's wrong with you?
I'm pure Evil
I'm still insane, in the best possible way.
I think Brian's idea of romance is using lube.
Your rage caused the meteor strike in Russia. The Antichrist would be proud of his minion.
You win with your thread. Most everything
It's a truck with a steel gate on the back. Just a statement of fact
Motec M820, AIM dash, ported 13B-RE Cosmo, 6-spd trans, 4.3 Torsen, custom twin wg fully divided mani, Custom 4" split into 2x 3" exhaust, Custom HMIC, Custom custom custom custom I like to welder stuff....
No Bolt-ons allowed. Dyno'ed @ Speed1 Tuned by me - 405rwhp on WG.... WM50 cuming soon.
-Angry Motherf*cker Mode ENGAGED-
|