oil pan braces

[Garfinkles Motor Works]

I have a few oil pan braces ready to ship . These have the groove milled in them so the actually put pressure on the rail .

[blwnrtr93]

What's the cost on these? Nevermind. I just found the thread where you are bringing some to the Gap.

[glenrx7]

Bump, for a good product we have been using these for our customer engines.

[blwnrtr93]

Thanks again for bringing these to the Gap and letting me pick your brain while there.

[justturbo2]

any more in stock

[Garfinkles Motor Works]

There are seven more ready to ship .

[AzEKnightz]

what is the price for it?

[Garfinkles Motor Works]

The price for the oil pan brace and the engine torque brace is ( each ) $ 125 if you send me a check or for Pay pal ,through Dubulup on the other forum is $ 130 .

[Twisted7]

Do you still have some left?

[Garfinkles Motor Works]

Yes I have a few, Speed For Sale may have some as well .

[Brent]

This is a great product!!! I run it on my silver FD and will be picking one up for my red one when I finally pull the engine.

David, I never did have a chance to get the measurements on the engine torque brace before I left , but I'm hoping to when I am home for 2 weeks in October... will that be an issue? Thanks!

Brent

[Garfinkles Motor Works]

No problem ,stay safe.

[justturbo2]

What is your paypal info
thanks

[Garfinkles Motor Works]

Oil pan braces are ready to send out ,11-06-08

[dregg100]

question: if my engine has a full oversized guru stud kit(machined block) would it be a waste of money to put one of these on?

[Garfinkles Motor Works]

If you are using the stock oil pan with drilled out holes then the brace is for you .The holes have made the pan rail weak and the brace willimprove things .The holes in the brace will to be drilled out as well .The brace is 3/16 thick and will still reinforce the pan to keep it from distorting .

[AzEKnightz]

Will this work well with stock oil pan and no modifications (I have a leakage >.<) Please let me know for I will paypal once confirmed. Thanks in advance.

p.s. Please pm for I dont check the forum alot nowadays. Thanks again.

-AzEKnightz

[Garfinkles Motor Works]

Pm to you and yes this will work on stock pans .Most people have stock pans ,some with studs and nuts . The groove cut in my brace is the feature that lets the brace do its job ,with out the groove the brace will not contact the pan rails width fully.

[fire85gslse]

These are a great brace. Once I installed mine I understood why this is the better brace out there.
Man, am I lucky to have a friend like David living so close to me and makes great products for my RX7's

[mc-don]

Is the oil pan brace still available? I have a leaking oil pan and would be interested in getting one.

[Garfinkles Motor Works]

THERE are a few ready to go

[TimeMachine]

I'd like to order one ASAP, I shall PM you with details :)

[MOBEONER]

I have received certain products from David my self and i can tell you first hand he takes pride on what he does and the parts are top notch.

[Garfinkles Motor Works]

I have a new batch ready to ship with the bolts and o-ring The price of the steel went up but the price will be the same .

[Red Baron]

Very much interested in one, how much and where do I send money???
Also what does the kit include and where can I see one??? PM or email me: red93r2@sbcglobal.net

[Garfinkles Motor Works]

They are $125 includes shipping $129 paypal .Includes high grade longer pan bolts (19) and longer motor mount bolts (6) . This is the only one with a milled groove to clear the pinch rail on the stock pan,so full presure is applied to the pan .

[speedjunkie]

I want to pick up one of these. What is your paypal?

[Garfinkles Motor Works]

garfinklemw@gmail.com

[lwnslw]

Anyone have pics ??

[Garfinkles Motor Works]

I think Howard Coleman does ,he uses them on the engines he builds .This is the only brace with a milled groove to fit over the pans pinch rail so full pressure is given across the rail .I drill the two missing holes in the late model pans and use all 19 ( included ) 6mm bolts .I notch the motor mount to clear the new bolt head . The motor mount bolts and the oil level sensor o-ring come with it as well .

[Bluewind]

This looks great, sending you a PM now!

[Garfinkles Motor Works]

I have a few more ready, do not wait to long.

[Halfbridge]

Hey David! Thanks for the invite to the forum :)

I am sending the $125 via PayPal right now. Thanks!

[Garfinkles Motor Works]

I have your address Adam and will ship the part tomorrow .Thank you.

[Halfbridge]

Thank you!

[Garfinkles Motor Works]

I sent you a PM with the tracking number .

[Red Baron]

$129 Paypal for the brace sent.

[Garfinkles Motor Works]

RB I will ship it tomorrow ,Only a few in stock .

[Rawbz08]

i will be ordering mine with in the next couple weeks ( set aside a ETB and a pan brace for me... thanks

[Garfinkles Motor Works]

Pulled from storage and saved .Running out of oil pan braces should I make more .

[Garfinkles Motor Works]

Sold out ,should I make more ?

[VIPNiSS]

Yes please! I am in dire need of one now.

[Garfinkles Motor Works]

Only two people in need ,that is not enough fo me to spend well over $1200 to have the cutting done plus getting the milling done at another shop then ordering the bolts and 0-rings .

[RXJJang]

i'm in for one as well

[Raksj04]

Will they fit the FC?

[Garfinkles Motor Works]

They will NOT fit the FC the motor mounts are different .

[pistons]

I'm in too, would it be wise to try to install in car? I would also like to do the engine mounts for the pan brace at the same time.

[lwnslw]

PM sent to David...

[Garfinkles Motor Works]

Not enough interest to go on .

[Garfinkles Motor Works]

Another batch will be ready in September if you need one you had better check on it now as about 20 of the 28 have been spoken for .

[rotarylyman]

PM sent to David

[Garfinkles Motor Works]

If you are reading the forum Then you will know that had another batch of oil pan braces made and they are selling now .If you need one email me to see if any are left .The cost is still $125 includes hardware and shipping in the USA . E-mail is garfinklemw@gmail.com

[Kman Art]

email sent

[Garfinkles Motor Works]

This run of braces is almost sold out ,If you need one first come first served .

[Garfinkles Motor Works]

Oil pan braces are SOLD OUT .If there are twenty presale orders I will do another run .Put your name on the thread in the 3rd gen section . Thanks to all who bought them in the past .

[Garfinkles Motor Works]

A new list has been started in the third gen section .4-30-2013

[Garfinkles Motor Works]

I HAVE OIL PAN BRACES READY TO SHIP AT THE SAME PRICE AS BEFORE .They are still $125 including all bolts ,o-ring and shipping in the USA . 7-10-2013

[Garfinkles Motor Works]

I have oil pan braces ready to ship ,those who said they wanted me to run another batch should at least reply .

[howard coleman]

David, i need another five.

howard

[Garfinkles Motor Works]

I have some braces ready two ship, todays date is 2 13 2014 .

[Garfinkles Motor Works]

I have a new batch ready to go ,today is 11-7-2014

[almoststockfc]

Hi David, I would be interested in one of the braces

[rasujo]

Hi David, I will take one too

[Garfinkles Motor Works]

Rasujo I will ship yours tomorrow ,thank you for the order.

[Rx7aholic]

Hey how can I place an order plus extra hardware such as the bolts?
Khris

[Garfinkles Motor Works]

Oil pan braces include the pan bolts longer motor mount bolts and the oil level O-ring . The price with shipping and handling in the USA is $125 .