Tegheim - Home made 4 rotor Wolvo 142

Tegheim · 07-02-2012, 12:08 AM

Thanks guys! I will try to keep the pace now when I feel the flow.
Some days, I just wanna blow the whole shit up in the air

Tegheim · 07-05-2012, 02:33 PM

Today I did a mockup to see that the coilover-lenght could ba about right, and that the angles looks good in the car.
I also got som used rear tires, also to mockup and make sure the fit later.
225/45-17" Front
255/40-17" Rear

GySgtFrank · 07-05-2012, 03:06 PM

Quote:

Originally Posted by Tegheim

Thanks guys! I will try to keep the pace now when I feel the flow.
Some days, I just wanna blow the whole shit up in the air

I think we all feel that way with a project sometimes. Take a week or so off, have a beer, or two, or three, or.... with guys that are tracking their cars. Run a few laps of Gran Turismo, etc. Bam! good to go, ready for more work.

Hansen · 07-05-2012, 08:36 PM

I see that you say "four rotor" build. how about some images of the motor build?

My5ABaby · 07-05-2012, 09:41 PM

Quote:

Originally Posted by Hansen

I see that you say "four rotor" build. how about some images of the motor build?

Look at the whole thread.

Tegheim · 07-06-2012, 12:06 AM

You got to have a car to put the engine in. There's alot of time there!

Mazdabater · 07-06-2012, 12:15 AM

Looking gorgeous as always buddy, do you have the shaft back yet?

Raksj04 · 07-06-2012, 12:31 AM

So how much of this car will you still be able to call a Volvo?

Mazdabater · 07-06-2012, 12:42 AM

I'm going to assume the badge. Lol

Tegheim · 07-06-2012, 07:13 AM

On the outside the car will look original, but rather low, about 150mm lower than stock

But Volvo have thought about this idea a looong time. This Badge the had on the P1800-model. I think they wanted to say something

Tegheim · 07-07-2012, 11:33 AM

I recieved a rod yesterday, Delrin, for bushings. My wife is happy with me as I am

Coming to these using a stainless steel sleeve model 16x2mm.

This is what it would look like, as common.

Then today I got to work hard because I do not have access to laser-cutter. Began to mill as deep as I dared, without them to come off, and the plate begins to vibrate and break the cutter. Then there has been much handwork! Good for me, to practice a bit. Continued on these!

Tegheim · 07-18-2012, 03:03 PM

Came up with an new idea about the Camber-adjustment. Simple to adjust with only one tool, and no need for deassembly anything around it.

4pc Ø30mm steel.
Did not have the possibility to use the CNC-lathe tonight, so it has been some therapy in the manual lathe.
M20x1.5 thread for streanght and good adjustments.

RICE RACING · 07-18-2012, 04:32 PM

You are a bad boy holding black steel in the three jaw!!!!

Tegheim · 07-18-2012, 05:00 PM

Why not? What else could I've done?

Raksj04 · 07-18-2012, 06:03 PM

Quote:

Could you put something next to those so we can get an idea of how big they are?

07-02-2012, 12:08 AM	#241
Tegheim Rotary Fanatic Join Date: Feb 2011 iTrader: (0) Posts: 210 Rep Power: 8	Thanks guys! I will try to keep the pace now when I feel the flow. Some days, I just wanna blow the whole shit up in the air Last edited by Tegheim; 07-05-2012 at 02:33 PM..

07-18-2012, 04:32 PM	#253
RICE RACING Don Mega Join Date: Dec 2008 Location: Utopia iTrader: (0) Posts: 1,688 Rep Power: 11	You are a bad boy holding black steel in the three jaw!!!! __________________ www.riceracing.com.au Worlds best Apex Seals Coil on Plug Water Injection ECU Calibration

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

07-05-2012, 02:33 PM	#242
Tegheim Rotary Fanatic Join Date: Feb 2011 iTrader: (0) Posts: 210 Rep Power: 8	Today I did a mockup to see that the coilover-lenght could ba about right, and that the angles looks good in the car. I also got som used rear tires, also to mockup and make sure the fit later. 225/45-17" Front 255/40-17" Rear

07-05-2012, 08:36 PM	#244
Hansen The Newbie Join Date: Jun 2012 Location: Cleveland, TX iTrader: (0) Posts: 4 Rep Power: 0	I see that you say "four rotor" build. how about some images of the motor build?

07-06-2012, 12:06 AM	#246
Tegheim Rotary Fanatic Join Date: Feb 2011 iTrader: (0) Posts: 210 Rep Power: 8	You got to have a car to put the engine in. There's alot of time there!

07-06-2012, 12:15 AM	#247
Mazdabater FC3S Join Date: Jun 2010 Location: Townsville, QLD, AUS iTrader: (0) Posts: 326 Rep Power: 8	Looking gorgeous as always buddy, do you have the shaft back yet?

07-06-2012, 12:31 AM	#248
Raksj04 I have Ultra power in me. Join Date: Sep 2011 iTrader: (2) Posts: 457 Rep Power: 7	So how much of this car will you still be able to call a Volvo?

07-06-2012, 12:42 AM	#249
Mazdabater FC3S Join Date: Jun 2010 Location: Townsville, QLD, AUS iTrader: (0) Posts: 326 Rep Power: 8	I'm going to assume the badge. Lol

07-06-2012, 07:13 AM	#250
Tegheim Rotary Fanatic Join Date: Feb 2011 iTrader: (0) Posts: 210 Rep Power: 8	On the outside the car will look original, but rather low, about 150mm lower than stock But Volvo have thought about this idea a looong time. This Badge the had on the P1800-model. I think they wanted to say something

07-07-2012, 11:33 AM	#251
Tegheim Rotary Fanatic Join Date: Feb 2011 iTrader: (0) Posts: 210 Rep Power: 8	I recieved a rod yesterday, Delrin, for bushings. My wife is happy with me as I am Coming to these using a stainless steel sleeve model 16x2mm. This is what it would look like, as common. Then today I got to work hard because I do not have access to laser-cutter. Began to mill as deep as I dared, without them to come off, and the plate begins to vibrate and break the cutter. Then there has been much handwork! Good for me, to practice a bit. Continued on these!

07-18-2012, 03:03 PM	#252
Tegheim Rotary Fanatic Join Date: Feb 2011 iTrader: (0) Posts: 210 Rep Power: 8	Came up with an new idea about the Camber-adjustment. Simple to adjust with only one tool, and no need for deassembly anything around it. 4pc Ø30mm steel. Did not have the possibility to use the CNC-lathe tonight, so it has been some therapy in the manual lathe. M20x1.5 thread for streanght and good adjustments.

07-18-2012, 05:00 PM	#254
Tegheim Rotary Fanatic Join Date: Feb 2011 iTrader: (0) Posts: 210 Rep Power: 8	Why not? What else could I've done?